Skip to main content

ASIC Miner ICERIVER KAS KS0 Profitability

ASIC Miner ICERIVER KAS KS0 Profitability In the realm of cryptocurrency mining, the Iceriver KAS KS0 miner has garnered widespread attention. Tailored specifically for the Kaspa network's KHeavyHash algorithm, it boasts high hashing power and low power consumption, making it an ideal choice for many miners. In this article, we will comprehensively assess IceRiver KS0 profitability while considering the Kaspa market conditions and the attributes of KS0 miner. Kaspa Market Dynamics Kaspa is a vibrant cryptocurrency network aimed at delivering high performance and scalability for everyday transactions. At the time of writing this article, the Kaspa coin trades at approximately $0.04959. But it's essential to note that cryptocurrency markets are highly susceptible to price volatility. Hence, investors must remain vigilant about market dynamics. Additionally, the Kaspa network's mining difficulty and reward mechanisms play a role in mining returns. Attributes of the IceRiver KS

How to solve the screen refresh failure of the Antminer L3+?

How to solve the screen refresh failure of the Antminer L3+?

The following kernel log faults are mainly for Antminer L3+; other Antminer models are for reference only.
spam fault log
Refresh screen failure means that the log keeps showing the same content repeatedly.

Troubleshooting method: 

When there is a screen refresh failure in the backstage kernel log, we need to focus on checking whether the voltages of the RI signal and CO signal of the chip are normal, generally starting from the first domain.
RI test method: adjust the fluke 15B+ multimeter to the DC gear, and place the red and black test pens on the heat sink and RI of the same domain respectively. Compare the measured voltage results with the resistance values of other chips in the same domain. If you find a BM1485 ASIC chip with abnormal chip voltage or fault, it is recommended to re-solder or replace it.
BM1485 ASIC chip
CO test method: quickly find the faulty chip through the short-circuit test point "CO."
We can ground "CO" to prevent signal transmission so that the damaged chip can be found quickly.

Comments

Popular posts from this blog

How to test the voltage and ground value of the power supply unit of the Antminer S9 hash board?

How to test the voltage and ground value of the power supply unit of the Antminer S9 hash board? Antminer S9 hash board Antminer S9 hash board power supply unit Voltage and ground value test of Antminer S9 power supply unit 12V voltage test Test method: adjust the Fluke 15B+ multimeter to the DC gear; the red test lead is placed on the positive pole of the power interface of the hash board, and the black test lead is placed on the negative pole of the power interface. PIC chip voltage test There is a white dot next to the PIC chip, which is 1st Pin. Test method : Adjust the Fluke 15B+ multimeter to the DC gear, measure whether the 1st Pin of the PIC chip has output, and the normal voltage is about 3.3V. If there is no 3.3V, please check the connection status of the hash board test line to see if the hash board is normal; if not, you need to re-program the PIC. MOS tube voltage test There is a black dot on the MOS tube, which is the 1st Pin (Figure 1). This is because the voltage of t

How to repair antminer T17 Hashboard and repair guide manual download

How to repair antminer T17 Hashboard and repair guide manual download This version contains the basic circuit schematic diagram and chip signal direction and voltage introduction We currently publish in Chinese and the English version will be released soon Basic overview: Antminer T17 single hash board uses a total of 30 hash chips, the model is "BM1397", and the signal direction is sequentially transmitted from U1 to U30. Signal direction: "CLK / CO / BO / RST", transferred from U1 to U30, "RI" is transferred from U30 to U1 It also passes 5 test points for testing and maintenance The five test points are: CLK-CO-RI-BO-RST (Please note: The location of the test points in different voltage domains are also different, please refer to the picture notes) For notes and instructions on the test points, please see the following articles: The whole board has 30 chips, divided into 10 voltage domains, and each voltage domain contains 3 chips For the description of

How to repair ASIC miner hash board

How to repair ASIC miner hash board Important parts of ASIC miners – Hash board One  ASIC miner consists of 3 to 5 Hash board, a control board, a casing, and software, among which the Hash board are easiest  to broken. because the ASIC bitcoin miner hash board consists of many serially connected ASIC chips. When they work, they will be in a high-temperature environment for a long time. In this environment, it is easy to burn the chip or scatter the solder due to high temperature which makes the hash board or the mining machine unable to work and no hash rate. How to quickly detective which chips broken it’s the most important when we repairing ASIC miners The Antminer chips fixture fast efficient and easy to use Bitmain Antminer repair inspection tool The ASIC bitcoin miner hash board consists of many serially connected ASIC chips. When they work, they will be in a high-temperature environment for a long time. In this environment, it is easy to burn the chip or scatter the solder du