Skip to main content

ASIC Miner ICERIVER KAS KS0 Profitability

ASIC Miner ICERIVER KAS KS0 Profitability In the realm of cryptocurrency mining, the Iceriver KAS KS0 miner has garnered widespread attention. Tailored specifically for the Kaspa network's KHeavyHash algorithm, it boasts high hashing power and low power consumption, making it an ideal choice for many miners. In this article, we will comprehensively assess IceRiver KS0 profitability while considering the Kaspa market conditions and the attributes of KS0 miner. Kaspa Market Dynamics Kaspa is a vibrant cryptocurrency network aimed at delivering high performance and scalability for everyday transactions. At the time of writing this article, the Kaspa coin trades at approximately $0.04959. But it's essential to note that cryptocurrency markets are highly susceptible to price volatility. Hence, investors must remain vigilant about market dynamics. Additionally, the Kaspa network's mining difficulty and reward mechanisms play a role in mining returns. Attributes of the IceRiver KS

What to do with outdated bitcoin miners?

What to do with outdated bitcoin miners?

In the case of considering the cost of electricity, the life cycle of miners is generally about 3-5 years. That is to say, after 3-5 years, the mining performance of miners and the current currency price may not be enough to cover the electricity consumption. In such a case, the choice of the vast majority of miners can only be shut down. Since it is no longer possible to continue mining, where will these outdated miners go?
outdated bitcoin miners

Whole miners resell

For miners who can only dig out electricity bills, for self-pay electricity users, there is no need to continue digging. At this time, if the miners are sold to free electricity users, it will be more cost-effective than dismantling the parts and selling the waste products. Because free electricity users are not sensitive to electricity bills, miners can continue to use their waste heat.
When selling outdated miners, you must break through your psychological barriers. After all, if you buy thousands of dollars, you may sell for only tens of dollars, and there is a considerable price difference. There is no profit for self-funded electric miners, and it isn't very sensible for miners to keep it in their hands. As long as the recycling price is higher than the price of dismantled garbage, it is cost-effective. It's better than holding it in your hand and selling garbage after a while.

Buck and frequency reduction

Although at the factory standard frequency, miners are already unprofitable for mining. However, each type of miner chip can work at various voltage frequencies. Therefore, different voltages and frequencies can get different speed-to-power ratios. The most famous one is Antminer.
However, many miners currently facing obsolescence do offer frequency adjustments. But unfortunately, the working voltage of miners cannot be adjusted in the control software. So if you reduce the operating frequency, the speed will drop, and the temperature will also drop. However, because the voltage has not dropped, the power consumption will still be reduced proportionally, so the speed and energy consumption ratio are still the same; using such a miner mining still only digs out electricity bills.
So how can we lower the voltage? Only the power supply part in the miner's circuit is hard-modified because the power supply part of the miner is digitally controlled DC-DC step-down. By adjusting the resistance value of the peripheral sampling resistor of the IC, the working voltage of the miner can be lowered. Under normal circumstances, only one or two chip resistors need to be replaced.

Dismantling and selling accessories

Although miners cannot be used for mining, the high-power power supplies of miners are reusable, and the price of buying new power supplies for miners is mostly around $200-300. Second-hand high-power power supplies can also be sold for tens of dollars, depending on the brand. If you buy a new miner, you can use it repeatedly as long as the power supply can be used universally. Some new miners do not have a power supply and need to buy them separately. Therefore, it is a better choice for old miners with a power supply.
In addition, the control board inside the miner can be brushed into the control board of other types of miners, and the chips of some miners can also be used universally and can also be used for later disassembly and recycling.

Comments

Popular posts from this blog

How to repair antminer T17 Hashboard and repair guide manual download

How to repair antminer T17 Hashboard and repair guide manual download This version contains the basic circuit schematic diagram and chip signal direction and voltage introduction We currently publish in Chinese and the English version will be released soon Basic overview: Antminer T17 single hash board uses a total of 30 hash chips, the model is "BM1397", and the signal direction is sequentially transmitted from U1 to U30. Signal direction: "CLK / CO / BO / RST", transferred from U1 to U30, "RI" is transferred from U30 to U1 It also passes 5 test points for testing and maintenance The five test points are: CLK-CO-RI-BO-RST (Please note: The location of the test points in different voltage domains are also different, please refer to the picture notes) For notes and instructions on the test points, please see the following articles: The whole board has 30 chips, divided into 10 voltage domains, and each voltage domain contains 3 chips For the description of

How to repair ASIC miner hash board

How to repair ASIC miner hash board Important parts of ASIC miners – Hash board One  ASIC miner consists of 3 to 5 Hash board, a control board, a casing, and software, among which the Hash board are easiest  to broken. because the ASIC bitcoin miner hash board consists of many serially connected ASIC chips. When they work, they will be in a high-temperature environment for a long time. In this environment, it is easy to burn the chip or scatter the solder due to high temperature which makes the hash board or the mining machine unable to work and no hash rate. How to quickly detective which chips broken it’s the most important when we repairing ASIC miners The Antminer chips fixture fast efficient and easy to use Bitmain Antminer repair inspection tool The ASIC bitcoin miner hash board consists of many serially connected ASIC chips. When they work, they will be in a high-temperature environment for a long time. In this environment, it is easy to burn the chip or scatter the solder du

Antminer APW9 and APW9+ Power Supply Repair Guide

Antminer APW9 and APW9+ Power Supply Repair Guide Apw9 Apw9+ is a high-power PSU with 2 single-phase AC inputs and 2   DC outputs. 1: 14.5v-21v voltage adjustable output, maximum current 170A 2: 12v voltage fixed output, maximum current 12A The circuit board layout is mainly divided into: 1A - The first AC input and EMI circuit 1B - PFC and MOS circuit 1C - 12V auxiliary circuit and VCC circuit 2A -  2nd AC input and EMI circuit 2B - PFC and MOS circuit 2C - 12V auxiliary circuit and VCC circuit 2D - 12V output port and PIC communication port   The vulnerable parts of PSU are: fuse, MOS, rectifier bridge A more detailed circuit diagram is provided in the document for  Reference See more details here  Antminer manuals and repair guide