Skip to main content

ASIC Miner ICERIVER KAS KS0 Profitability

ASIC Miner ICERIVER KAS KS0 Profitability In the realm of cryptocurrency mining, the Iceriver KAS KS0 miner has garnered widespread attention. Tailored specifically for the Kaspa network's KHeavyHash algorithm, it boasts high hashing power and low power consumption, making it an ideal choice for many miners. In this article, we will comprehensively assess IceRiver KS0 profitability while considering the Kaspa market conditions and the attributes of KS0 miner. Kaspa Market Dynamics Kaspa is a vibrant cryptocurrency network aimed at delivering high performance and scalability for everyday transactions. At the time of writing this article, the Kaspa coin trades at approximately $0.04959. But it's essential to note that cryptocurrency markets are highly susceptible to price volatility. Hence, investors must remain vigilant about market dynamics. Additionally, the Kaspa network's mining difficulty and reward mechanisms play a role in mining returns. Attributes of the IceRiver KS...

How to test the voltage and ground value of the Antminer S17 Pro hash board power supply unit?

How to test the voltage and ground value of the Antminer S17 Pro hash board power supply unit?

Antminer S17 Pro hash board

Antminer S17 Pro hash board

Antminer S17 Pro hash board power supply unit

Antminer S17 Pro power supply unit

Voltage and ground value test of Antminer S17 Pro power supply unit

1. 18V voltage test

Test method: Fluke 15B + multimeter DC gear, the red test lead is placed on the positive pole of the power interface of the hash board, and the black lead is placed on the negative pole of the power interface.
Antminer S17 Pro 18V voltage test point

2. PIC chip voltage test

There is a black dot on the PIC chip, that is the 1st Pin.
Test method: Fluke 15B + multimeter DC gear, measure whether the 9th Pin of the PIC chip has a voltage output; the normal voltage is about 3.3V. If there is no 3.3V, please check the connection status of the hash board test cable to see if the hash board is normal. If it is not normal, you need to reprogram the PIC.
Antminer S17 Pro PIC schematic

3. MOS tube voltage test

There is a white dot next to the MOS tube, which is the 1st Pin. Therefore, the voltage of the MOS tube is the 1st Pin input and the 8th Pin output.
Test method: Fluke 15B + multimeter DC gear, the black test lead is placed on the negative pole of the capacitor, the red test lead is placed on the 1st or 8th Pin of the MOS tube, the input and output values of the MOS tube voltage can be measured, normal will have 18V input and output.
If the voltage is abnormal, it is necessary to measure the ground value of the MOS tube.
Test method for ground value: Fluke 15B + multimeter diode gear, red test lead is placed on the negative electrode of the capacitor, and black test lead is placed on the 1st or 8th Pin of the MOS tube. If the ground value is abnormal, replace the MOS tube. (To judge whether the resistance value of the MOS tube is abnormal, you can compare it with other MOS tubes)
Antminer S17 Pro hash board MOS tube voltage test point

Antminer S17 Pro hash board MOS schematic

4. LDO 1.8V and PLL 0.8V output voltage test

There is a white dot next to LDO 1.8V, which is the 1st Pin. The LDO 1.8V voltage is the 1st Pin input and the 5th Pin output.
Test method: Fluke 15B + multimeter DC gear, the black test lead is placed on the heat sink of the same domain, the red test lead is placed on the 1st Pin, normally there will be a voltage input of 3.2V, and the black test lead is placed on the 5th Pin, normally there will be 1.8V output.
There is a white dot next to PLL 0.8V, which is the 1st Pin. PLL 0.8V voltage is the 1st Pin input and the5th Pin output.
Test method: Fluke 15B + multimeter DC gear, the black test lead is placed on the heat sink of the same domain, the red test lead is placed on the 1st Pin, normally there will be a voltage input of 1.8V, the red test lead is placed on the 5th Pin, normally there will be 0.8V output.
If the voltage is abnormal, it is necessary to measure the ground value of LDO 1.8V and PLL 0.8V.
Ground value detection method: Fluke 15B + multimeter diode gear, the red test lead is placed on the heat sink of the same domain, and the black test lead is placed on the 1st Pin. If the ground value is abnormal, replace the corresponding LDO 1.8V and PLL 0.8V. (To judge whether the resistance of LDO 1.8V and PLL 0.8V is abnormal, you can compare other LDO 1.8V and PLL 0.8V)
Antminer S17 Pro hash board 1.8V 0.8V output voltage test
Antminer S17 Pro hash board 1.8V power supply circuit diagram
Antminer S17 Pro hash board 0.8V power supply circuit diagram

5. 24V voltage test

Through the two ends of the black capacitor, the 24V voltage can be measured.
Test method: Fluke 15B + multimeter DC gear is red, the red test lead is placed on the positive electrode of the capacitor, and the black test lead is placed on the negative electrode of the capacitor.
Antminer S17 Pro hash board 24V voltage test point

Comments

Popular posts from this blog

How to repair antminer T17 Hashboard and repair guide manual download

How to repair antminer T17 Hashboard and repair guide manual download This version contains the basic circuit schematic diagram and chip signal direction and voltage introduction We currently publish in Chinese and the English version will be released soon Basic overview: Antminer T17 single hash board uses a total of 30 hash chips, the model is "BM1397", and the signal direction is sequentially transmitted from U1 to U30. Signal direction: "CLK / CO / BO / RST", transferred from U1 to U30, "RI" is transferred from U30 to U1 It also passes 5 test points for testing and maintenance The five test points are: CLK-CO-RI-BO-RST (Please note: The location of the test points in different voltage domains are also different, please refer to the picture notes) For notes and instructions on the test points, please see the following articles: The whole board has 30 chips, divided into 10 voltage domains, and each voltage domain contains 3 chips For the description of ...

ASIC Miner ICERIVER KAS KS0 Profitability

ASIC Miner ICERIVER KAS KS0 Profitability In the realm of cryptocurrency mining, the Iceriver KAS KS0 miner has garnered widespread attention. Tailored specifically for the Kaspa network's KHeavyHash algorithm, it boasts high hashing power and low power consumption, making it an ideal choice for many miners. In this article, we will comprehensively assess IceRiver KS0 profitability while considering the Kaspa market conditions and the attributes of KS0 miner. Kaspa Market Dynamics Kaspa is a vibrant cryptocurrency network aimed at delivering high performance and scalability for everyday transactions. At the time of writing this article, the Kaspa coin trades at approximately $0.04959. But it's essential to note that cryptocurrency markets are highly susceptible to price volatility. Hence, investors must remain vigilant about market dynamics. Additionally, the Kaspa network's mining difficulty and reward mechanisms play a role in mining returns. Attributes of the IceRiver KS...

Antminer S19 / S19 Pro Setup

Antminer S19 / S19 Pro Setup I . Check before using Antminer S19 / S19 Pro 1. New miners sign for inspection a. When receiving new miners, check whether the appearance of the package is damaged; b. After unpacking, check whether the miner's casing is deformed, whether the fan and connecting line are damaged, and whether the cable is damaged; c. Check whether the miners have abnormal noise; d. Check whether the cable is loose and the fan plug is loose. If it is loose, plug it in in time. 2. Instructions for use a. Miners cannot use routers or switches  with POE function to connect; b. Miners can only connect to routers or switches by wire; c. The recommended temperature is 25 to 30 degrees; d. It is recommended to use the ambient humidity below 65%RH; e. Pay attention to dust and catkins so as not to corrode the hash board or cause the heat of the miners not to dissipate; f. To enter the miners backstage, it is recommended to use Google or Firefox browser. Note:  It is str...