ZEUS MINING BLOG

Whatsminer ZYNQ control board firmware burning tutorial 1. Unzip Win32DiskImager-0.9.5-binary, as shown in the figure: 2. Insert the card reader equipped with the memory card, and then run the Win32DiskImager application after decompression, as shown in the figure: 3. After running, the following interface will be displayed: 4. Click the icon of the folder, select the image with the "zynq" identifier in the SD card image, and then click Open to import it into Win32DiskImager, as shown in the following figure: 5. Go back to the Win32DiskImager interface, and click "Write" to burn the card; 6. After the card is burned successfully, the following interface will pop up: So far, the SD card of the ZYNQ control board has been completed. 7. Burn; after the SD card is made, you can prepare the firmware for burning. First, power off the miner, take out the control board from the case box, jump the jumper between JP1 and JP2 of the control board to VCC, set the firmware versi...

Bit Express 21T R1 Miner Evaluation Bit Express is a new army of miners developed by an internationally renowned investment company with the world's third-largest mobile phone chip company. TSMC's pipeline produces the chips. The following is a test of the use of Bit Express R1 miners. Bit Express R1 official parameters: Hash rate: 21T/S (±5%) Power consumption: 1300 W (±5%) Algorithm: SHA256 Power consumption ratio: 62W/TH AC input range: 176V-264Vac Chip: A1000 12nm chip Size: 447.3*150.3*270.4mm Weight: 8.2KG (net weight); 9.4KG (with power cord and packing box) Network Connection: Ethernet Heat dissipation: 1*14038 fan Noise: 71dB Operating environment: working temperature (0℃~40℃), working humidity (5%RH~95%RH), non-condensing. Miner appearance The body shell is made of aluminum alloy precision die-casting design, which can provide vital protection for the Hash board and improve the heat dissipation efficiency. Integrated design, easy to transport and put on the shelf. Min...

How to repair the common faults of the Whatsminer M20S hash board? This article will analyze the failure of the M20S hash board test log from the following aspects: Fault 1: The number of reports of single-board test chips is incomplete Test log phenomenon: The test log shows that the RST signal of the hash board is normal, the temperature sensor is normal, and the SN code is normal, but the number of ASIC chips is not complete. Normally, 105 chips should be found, but only 73 chips were actually found. Cause analysis: "The number of single-board test chips is incomplete" indicates that the power supply unit of the Hash board is normal. Therefore, you can check the voltage of the RXD, TXD, and CLK signals and then find the faulty chip. Check method: 1. Measure the RXD signal voltage (the RXD signal voltage is transmitted from the first chip to the last chip); its signal voltage usually is 1.8V. Generally, the investigation starts from the RXD signal of the first and last chip...

Baikal MINI X11 ASIC Miner Mining Tutorial The Baikal MINI X11 ASIC miner is compact and has an efficiency ratio of 150MH/40 W. Miner specifications Brand Baikal Mini X11 Miner Hash Rate 150 MH/s ± 5% Power Consumption 40W Cooling 1 * fan Network Connection Ethernet PSU NO PSU included. It needs a 12V5A Switching Power Adapter as PSU (Plug specifications: Outer Diameter 5.5mm; Inner Diameter 2.5mm). A “6pin to DC” convert cable is included. PSU Recommend 12V5A Switching Power Adapter In this tutorial, we will use the CoinMine.pl mining pool to explain the miner mining tutorial for you. PSU preparation The miner has no built-in power supply; you need extra preparation. It is recommended to use Miner 12V5A switching power adapter; the interface type is an outer diameter of 5.5mm; an inner diameter of 2.5mm. Miner connection · LAN port on the same router to which the miner and computer are connected. · This is the miner you received. · There are Ethernet ports, power connection ports,...

Whatsminer H6 control board firmware burning tutorial H6 SD card program is suitable for Whatsmin M3x, M2x series. 1. Download and unzip the "H6 SD Card Program" from Whatsminer's official website . 2. Insert the card reader with the memory card into the PC and run the unzipped PhoenixCard application. 3. After opening, the following interface will be displayed. 4. Select the firmware, and select the image file with IMG in the version file. 5. Click "Burning Card." Note: If the card burning fails, first select "Recovery Card," then close it, and then follow the steps 2~3 to cycle. The card burning process takes about 1 or 2 minutes, and the card will display green when the card is burned successfully, as shown in the figure: 6. After burning the card, take out the card, insert it into the card slot of the H6 control board, insert it according to the direction shown in the figure, and then power on (Note: the H6 control board does not need jumpers). Dur...