Skip to main content

ASIC Miner ICERIVER KAS KS0 Profitability

ASIC Miner ICERIVER KAS KS0 Profitability In the realm of cryptocurrency mining, the Iceriver KAS KS0 miner has garnered widespread attention. Tailored specifically for the Kaspa network's KHeavyHash algorithm, it boasts high hashing power and low power consumption, making it an ideal choice for many miners. In this article, we will comprehensively assess IceRiver KS0 profitability while considering the Kaspa market conditions and the attributes of KS0 miner. Kaspa Market Dynamics Kaspa is a vibrant cryptocurrency network aimed at delivering high performance and scalability for everyday transactions. At the time of writing this article, the Kaspa coin trades at approximately $0.04959. But it's essential to note that cryptocurrency markets are highly susceptible to price volatility. Hence, investors must remain vigilant about market dynamics. Additionally, the Kaspa network's mining difficulty and reward mechanisms play a role in mining returns. Attributes of the IceRiver KS

Innosilicon T3-43T Bitcoin Miner Evaluation

Innosilicon T3-43T Bitcoin Miner Evaluation

Innosilicon T3-43T is a bitcoin miner with an official hash rate of 43T and power consumption of 2100W. After unpacking, you need to check whether the miner's warranty sticker is damaged. Then, please pick up the miner and shake it slightly. If there is a collision between metals, it is recommended to contact the after-sales service. Miners use an all-in-one design. The shell is die-casted by aluminum material, the size is 430mm*141mm*220mm, and the net weight is 8.92 kg. Compared with the Innosilicon T2T model, it is smaller and lighter in weight. The interior of the miner is also made of the previous vertical placement was changed to horizontal placement.
Innosilicon T2T-32T size
Innosilicon T2T-32T
The model, hash rate, identification code, and instructions are posted on the side of the miner. The power requirement is 200-240AC, the IP acquisition method is DHCP (automatic acquisition). The login user name and password are both admin, and press and hold the reset button for 5-10 seconds to restore to factory settings.
Innosilicon T3-43T miner
Settings button
Miner air inlet.
miner air inlet
Official website query miner power supply rated power is 2500W, power conversion efficiency ≥ 93%, use data cable to connect with miner hash board, power supply has its switch, which is convenient for miners to use and maintain. Unfortunately, the power plug and the control board network cable plug are not one the direction may have a specific impact on the upper and lower racks, and the power module of the T3 has exceeded 2000W. Therefore, buying a power cable with a 3 * 2.0mm core is recommended.
miner ports

The IP setting button functions as follows:

1. Press the IP set key for 1-4 seconds;
(1) Send the miner's IP to the "Set IP" tool;
(2) Cooperate with the "Set IP" tool to set the miner to a static IP within the range specified by the tool.
2. Press and hold the IP set button for 4-15 seconds, the static IP will become a dynamic IP, and the mining pool settings will be restored to the default settings;
3. Press and hold the IP set button for more than 15 seconds to switch the miner IP to a static IP and restore the IP to the default IP 192.168.1.254.

Reset key function:

Press the reset button to restart the miner, long press for 5-10 seconds to restore to factory settings.

Innosilicon T3-43T Installation Setup

The factory default of the miner is DHCP mode; you can log in to the local router to find the IP address of the miner named "lnnominer" or use the IP scanning tool to find the IP of the miner.
sign in interface
After logging in, you need to make two modifications. One is to modify the mining pool settings so that the miners mined can enter your wallet smoothly, and the other is to modify the operating mode of the miners.
Click "Settings/Pools" to enter the mining pool setting page, modify the mining pool address and miner name in the "Pool 1" main mining pool, password "1234" or "X," and then modify the backup mining pools "Pool 2" and "Pool 3" mining pool address and miner name, click "Update Pools" after setting to update and save the mining pool, and the miner will automatically restart.
Select the operation mode of the miner. Innosilicon has preset 4 operation modes for the T3-43T, making the miner operating in 4 modes: low energy consumption, balanced, factory (default), and high hash rate, which are convenient and straightforward. Miners can freely choose according to the situation of the mining farm. After selecting, click "Save" to save.
In the "Settings" setting page, in addition to modifying the mining pool, you can also modify the user account information. You can also modify the user name and password to prevent others from modifying the mining address and miner name. Next, enter the "Settings/Network" page, and modify the IP address as dynamic or static as needed. After the modification is completed, click the "Update" button on the lower side to save the currently modified settings.
miner operation data
After the power is turned on, the standby power consumption is about 25W, and the startup noise is 69.5 decibels. Next, turn on the power supply and turn on the switch to check whether the two fans of the miner can work normally. If the fans are damaged or cannot work normally, they should be replaced in time.
noise test

Temperature

The temperature of each part of the miner is as follows. When the air inlet temperature is 28 degrees, the temperature of the air outlet of the miner is 45.6 degrees, and the peak value is 48 degrees. The temperature of the power outlet is about 35 degrees, and the temperature of the power supply and the miner connecting piece is about 32 degrees.
mining pool information
Mining pool reception.
miner power consumption test

Summarize

• The actual measured hash rate of miners reached 42.98T, which is currently the most advantageous in the hash rate ranking among spot miners in the market;
• Miners have adopted innovative, dynamic frequency adjustment technology, with a comprehensive power consumption ratio of about 49.8W/T, leading the industry;
• The miner console has 4 preset adjustable mining modes that can be switched freely, which can appropriately reduce power consumption or properly overclock, but it should be noted that the high hash rate mode has specific requirements on power supply and cables;
• Smaller and lighter in size and weight than T2T-32T, with better control of noise level;
• Both the front and rear fans of the heat dissipation are equipped with fan protection nets, which ensures the safety of the mining production process;
• After a 24-hour test on miners, the backstage page curve and the mining pool's receiving hash rate curve are stable;
• The backstage control page graphically displays the main parameters of the miner's operation, and the real-time hash rate values of the three hash boards are displayed separately, and the operation status is clear at a glance;
• Miners use an all-in-one design, which is easy to use;
• Innosilicon T3-43T takes into account the anti-scratching of the data cable and adds the night eye protection function to the control page. These are more thoughtful designs, but the bottom anti-skid pad is missing. It is recommended to keep it.
The content and pictures of this article are from the Internet, compiled and edited by ZEUS MINING.

Comments

Popular posts from this blog

How to repair ASIC miner hash board

How to repair ASIC miner hash board Important parts of ASIC miners – Hash board One  ASIC miner consists of 3 to 5 Hash board, a control board, a casing, and software, among which the Hash board are easiest  to broken. because the ASIC bitcoin miner hash board consists of many serially connected ASIC chips. When they work, they will be in a high-temperature environment for a long time. In this environment, it is easy to burn the chip or scatter the solder due to high temperature which makes the hash board or the mining machine unable to work and no hash rate. How to quickly detective which chips broken it’s the most important when we repairing ASIC miners The Antminer chips fixture fast efficient and easy to use Bitmain Antminer repair inspection tool The ASIC bitcoin miner hash board consists of many serially connected ASIC chips. When they work, they will be in a high-temperature environment for a long time. In this environment, it is easy to burn the chip or scatter the solder du

How to repair antminer T17 Hashboard and repair guide manual download

How to repair antminer T17 Hashboard and repair guide manual download This version contains the basic circuit schematic diagram and chip signal direction and voltage introduction We currently publish in Chinese and the English version will be released soon Basic overview: Antminer T17 single hash board uses a total of 30 hash chips, the model is "BM1397", and the signal direction is sequentially transmitted from U1 to U30. Signal direction: "CLK / CO / BO / RST", transferred from U1 to U30, "RI" is transferred from U30 to U1 It also passes 5 test points for testing and maintenance The five test points are: CLK-CO-RI-BO-RST (Please note: The location of the test points in different voltage domains are also different, please refer to the picture notes) For notes and instructions on the test points, please see the following articles: The whole board has 30 chips, divided into 10 voltage domains, and each voltage domain contains 3 chips For the description of

Antminer APW9 and APW9+ Power Supply Repair Guide

Antminer APW9 and APW9+ Power Supply Repair Guide Apw9 Apw9+ is a high-power PSU with 2 single-phase AC inputs and 2   DC outputs. 1: 14.5v-21v voltage adjustable output, maximum current 170A 2: 12v voltage fixed output, maximum current 12A The circuit board layout is mainly divided into: 1A - The first AC input and EMI circuit 1B - PFC and MOS circuit 1C - 12V auxiliary circuit and VCC circuit 2A -  2nd AC input and EMI circuit 2B - PFC and MOS circuit 2C - 12V auxiliary circuit and VCC circuit 2D - 12V output port and PIC communication port   The vulnerable parts of PSU are: fuse, MOS, rectifier bridge A more detailed circuit diagram is provided in the document for  Reference See more details here  Antminer manuals and repair guide